 |
| Bus run by biodiesel |
Biodiesel refers to a vegetable oil- or animal fat-based diesel fuel consisting of long-chain alkyl (methyl, propyl or ethyl) esters. Biodiesel is typically made by chemically reacting lipids (e.g., vegetable oil, animal fat (tallow)) with an alcohol.
Biodiesel is meant to be used in standard diesel engines and is thus distinct from the vegetable and waste oils used to fuel converted diesel engines. Biodiesel can be used alone, or blended with petrodiesel. Biodiesel can also be used as a low carbon alternative to heating oil.
The National Biodiesel Board (USA) also has a technical definition of "biodiesel" as a mono-alkyl ester.
 |
| Space-filling model of methyl linoleate, or linoleic acid methyl ester, a common methyl ester produced from soybean or canola oil and methanol |
Blends
Biodiesel sample
Blends of biodiesel and conventional hydrocarbon-based diesel are products most commonly distributed for use in the retail diesel fuel marketplace. Much of the world uses a system known as the "B" factor to state the amount of biodiesel in any fuel mix:
100% biodiesel is referred to as B100, while
20% biodiesel, 80% petrodiesel is labeled B20
5% biodiesel, 95% petrodiesel is labeled B5
2% biodiesel, 98% petrodiesel is labeled B2
Blends of less than 20% biodiesel can be used in diesel equipment with no, or only minor modifications , although certain manufacturers do not extend warranty coverage if equipment is damaged by these blends. The B6 to B20 blends are covered by the ASTM D7467 specification. Biodiesel can also be used in its pure form (B100), but may require certain engine modifications to avoid maintenance and performance problems. Blending B100 with petroleum diesel may be accomplished by:
Mixing in tanks at manufacturing point prior to delivery to tanker truck
Splash mixing in the tanker truck (adding specific percentages of Biodiesel and petroleum diesel)
In-line mixing, two components arrive at tanker truck simultaneously.
Metered pump mixing, petroleum diesel and Biodiesel meters are set to X total volume, transfer pump pulls from two points and mix is complete on leaving pump.
Applications
Biodiesel can be used in pure form (B100) or may be blended with petroleum diesel at any concentration in most injection pump diesel engines. New extreme high pressure (29,000 psi) common rail engines have strict factory limits of B5 or B20 depending on manufacturer. Biodiesel has different solvent properties than petrodiesel, and will degrade natural rubber gaskets and hoses in vehicles (mostly vehicles manufactured before 1992), although these tend to wear out naturally and most likely will have already been replaced with FKM, which is nonreactive to biodiesel. Biodiesel has been known to break down deposits of residue in the fuel lines where petrodiesel has been used. As a result, fuel filters may become clogged with particulates if a quick transition to pure biodiesel is made. Therefore, it is recommended to change the fuel filters on engines and heaters shortly after first switching to a biodiesel blend.
Distribution
Since the passage of the Energy Policy Act of 2005 biodiesel use has been increasing in the United States. In the UK, the Renewable Transport Fuel Obligation obliges suppliers to include 5% renewable fuel in all transport fuel sold in the UK by 2010. For road diesel, this effectively means 5% biodiesel.
Vehicular use and manufacturer acceptance
In 2005, Chrysler (then part of DaimlerChrysler) released the Jeep Liberty CRD diesels from the factory into the American market with 5% biodiesel blends, indicating at least partial acceptance of biodiesel as an acceptable diesel fuel additive. In 2007, DaimlerChrysler indicated intention to increase warranty coverage to 20% biodiesel blends if biofuel quality in the United States can be standardized.
Starting in 2004, the city of Halifax, Nova Scotia decided to update its bus system to allow the fleet of city buses to run entirely on a fish-oil based biodiesel. This caused the city some initial mechanical issues but after several years of refining, the entire fleet had successfully been converted.
In 2007, McDonalds of UK announced that it would start producing biodiesel from the waste oil byproduct of its restaurants. This fuel would be used to run its fleet.
Railway usage
British Train Operating Company Virgin Trains claimed to have run the world's first "biodiesel train", which was converted to run on 80% petrodiesel and only 20% biodiesel, and it is claimed it will save 14% on direct emissions.
The Royal Train on 15 September 2007 completed its first ever journey run on 100% biodiesel fuel supplied by Green Fuels Ltd. His Royal Highness, The Prince of Wales, and Green Fuels managing director, James Hygate, were the first passengers on a train fueled entirely by biodiesel fuel. Since 2007 the Royal Train has operated successfully on B100 (100% biodiesel).
Similarly, a state-owned short-line railroad in Eastern Washington ran a test of a 25% biodiesel / 75% petrodiesel blend during the summer of 2008, purchasing fuel from a biodiesel producer seated along the railroad tracks. The train will be powered by biodiesel made in part from canola grown in agricultural regions through which the short line runs.
Also in 2007 Disneyland began running the park trains on B98 biodiesel blends (98% biodiesel). The program was discontinued in 2008 due to storage issues, but in January 2009 it was announced that the park would then be running all trains on biodiesel manufactured from its own used cooking oils. This is a change from running the trains on soy-based biodiesel.
Aircraft use
A test flight has been performed by a Czech jet aircraft completely powered on biodiesel.Other recent jet flights using biofuel, however, have been using other types of renewable fuels.
As a heating oil
Biodiesel can also be used as a heating fuel in domestic and commercial boilers, a mix of heating oil and biofuel which is standardized and taxed slightly differently than diesel fuel used for transportation. It is sometimes known as "bioheat" (which is a registered trademark of the National Biodiesel Board [NBB] and the National Oilheat Research Alliance [NORA] in the U.S., and Columbia Fuels in Canada). Heating biodiesel is available in various blends; up to 20% biofuel is considered acceptable for use in existing furnaces without modification.
Older furnaces may contain rubber parts that would be affected by biodiesel's solvent properties, but can otherwise burn biodiesel without any conversion required. Care must be taken, however, given that varnishes left behind by petrodiesel will be released and can clog pipes- fuel filtering and prompt filter replacement is required. Another approach is to start using biodiesel as blend, and decreasing the petroleum proportion over time can allow the varnishes to come off more gradually and be less likely to clog. Thanks to its strong solvent properties, however, the furnace is cleaned out and generally becomes more efficient. A technical research paper describes laboratory research and field trials project using pure biodiesel and biodiesel blends as a heating fuel in oil fired boilers. During the Biodiesel Expo 2006 in the UK, Andrew J. Robertson presented his biodiesel heating oil research from his technical paper and suggested that B20 biodiesel could reduce UK household CO2 emissions by 1.5 million tons per year.
A law passed under Massachusetts Governor Deval Patrick requires all home heating diesel in that state to be 2% biofuel by July 1, 2010, and 5% biofuel by 2013.
Historical background
Transesterification of a vegetable oil was conducted as early as 1853 by scientists E. Duffy and J. Patrick, many years before the first diesel engine became functional. Rudolf Diesel's prime model, a single 10 ft (3 m) iron cylinder with a flywheel at its base, ran on its own power for the first time in Augsburg, Germany, on 10 August 1893 running on nothing but peanut oil. In remembrance of this event, 10 August has been declared "International Biodiesel Day".
It is often reported that Diesel designed his engine to run on peanut oil, but this is not the case. Diesel stated in his published papers, "at the Paris Exhibition in 1900 (Exposition Universelle) there was shown by the Otto Company a small Diesel engine, which, at the request of the French government ran on arachide (earth-nut or pea-nut) oil (see biodiesel), and worked so smoothly that only a few people were aware of it. The engine was constructed for using mineral oil, and was then worked on vegetable oil without any alterations being made. The French Government at the time thought of testing the applicability to power production of the Arachide, or earth-nut, which grows in considerable quantities in their African colonies, and can easily be cultivated there." Diesel himself later conducted related tests and appeared supportive of the idea. In a 1912 speech Diesel said, "the use of vegetable oils for engine fuels may seem insignificant today but such oils may become, in the course of time, as important as petroleum and the coal-tar products of the present time."
Despite the widespread use of fossil petroleum-derived diesel fuels, interest in vegetable oils as fuels for internal combustion engines was reported in several countries during the 1920s and 1930s and later during World War II. Belgium, France, Italy, the United Kingdom, Portugal, Germany, Brazil, Argentina, Japan and China were reported to have tested and used vegetable oils as diesel fuels during this time. Some operational problems were reported due to the high viscosity of vegetable oils compared to petroleum diesel fuel, which results in poor atomization of the fuel in the fuel spray and often leads to deposits and coking of the injectors, combustion chamber and valves. Attempts to overcome these problems included heating of the vegetable oil, blending it with petroleum-derived diesel fuel or ethanol, pyrolysis and cracking of the oils.
On 31 August 1937, G. Chavanne of the University of Brussels (Belgium) was granted a patent for a "Procedure for the transformation of vegetable oils for their uses as fuels" (fr. "Procédé de Transformation d’Huiles Végétales en Vue de Leur Utilisation comme Carburants") Belgian Patent 422,877. This patent described the alcoholysis (often referred to as transesterification) of vegetable oils using ethanol (and mentions methanol) in order to separate the fatty acids from the glycerol by replacing the glycerol with short linear alcohols. This appears to be the first account of the production of what is known as "biodiesel" today.
More recently, in 1977, Brazilian scientist Expedito Parente invented and submitted for patent, the first industrial process for the production of biodiesel.This process is classified as biodiesel by international norms, conferring a "standardized identity and quality. No other proposed biofuel has been validated by the motor industry."Currently, Parente's company Tecbio is working with Boeing and NASA to certify bioquerosene (bio-kerosene), another product produced and patented by the Brazilian scientist.
Research into the use of transesterified sunflower oil, and refining it to diesel fuel standards, was initiated in South Africa in 1979. By 1983, the process for producing fuel-quality, engine-tested biodiesel was completed and published internationally. An Austrian company, Gaskoks, obtained the technology from the South African Agricultural Engineers; the company erected the first biodiesel pilot plant in November 1987, and the first industrial-scale plant in April 1989 (with a capacity of 30,000 tons of rapeseed per annum).
Throughout the 1990s, plants were opened in many European countries, including the Czech Republic, Germany and Sweden. France launched local production of biodiesel fuel (referred to as diester) from rapeseed oil, which is mixed into regular diesel fuel at a level of 5%, and into the diesel fuel used by some captive fleets (e.g. public transportation) at a level of 30%. Renault, Peugeot and other manufacturers have certified truck engines for use with up to that level of partial biodiesel; experiments with 50% biodiesel are underway. During the same period, nations in other parts of the world also saw local production of biodiesel starting up: by 1998, the Austrian Biofuels Institute had identified 21 countries with commercial biodiesel projects. 100% Biodiesel is now available at many normal service stations across Europe.
In September 2005 Minnesota became the first U.S. state to mandate that all diesel fuel sold in the state contain part biodiesel, requiring a content of at least 2% biodiesel.
In 2008, ASTM published new Biodiesel Blend Specifications Standards.
Properties
Biodiesel has better lubricating properties and much higher cetane ratings than today's lower sulfur diesel fuels. Biodiesel addition reduces fuel system wear, and in low levels in high pressure systems increases the life of the fuel injection equipment that relies on the fuel for its lubrication. Depending on the engine, this might include high pressure injection pumps, pump injectors (also called unit injectors) and fuel injectors.
 |
| Older diesel Mercedes are popular for running on biodiesel. |
The calorific value of biodiesel is about 37.27 MJ/L. This is 9% lower than regular Number 2 petrodiesel. Variations in biodiesel energy density is more dependent on the feedstock used than the production process. Still these variations are less than for petrodiesel. It has been claimed biodiesel gives better lubricity and more complete combustion thus increasing the engine energy output and partially compensating for the higher energy density of petrodiesel.
Biodiesel is a liquid which varies in color — between golden and dark brown — depending on the production feedstock. It is immiscible with water, has a high boiling point and low vapor pressure. *The flash point of biodiesel (>130 °C, >266 °F) is significantly higher than that of petroleum diesel (64 °C, 147 °F) or gasoline (−45 °C, -52 °F). Biodiesel has a density of ~ 0.88 g/cm³, higher than petrodiesel ( ~ 0.85 g/cm³).
Biodiesel has virtually no sulfur content, and it is often used as an additive to Ultra-Low Sulphur Diesel (ULSD) fuel to aid with lubrication, as the sulfur compounds in petrodiesel provide much of the lubricity.
Material compatibility
Plastics: High density polyethylene (HDPE) is compatible but polyvinyl chloride (PVC) is slowly degraded. Polystyrenes are dissolved on contact with biodiesel.
Metals: Biodiesel has an effect on copper-based materials (e.g. brass), and it also affects zinc, tin, lead, and cast iron. Stainless steels (316 and 304) and aluminum are unaffected.
Rubber: Biodiesel also affects types of natural rubbers found in some older engine components. Studies have also found that fluorinated elastomers (FKM) cured with peroxide and base-metal oxides can be degraded when biodiesel loses its stability caused by oxidation. Commonly used synthetic rubbers FKM- GBL-S and FKM- GF-S found in modern vehicles were found to handle biodiesel in all conditions.
Technical standards
Biodiesel standard
Biodiesel has a number of standards for its quality including European standard EN 14214, ASTM International D6751, and others.
Low Temperature Gelling
When biodiesel is cooled below a certain point, some of the molecules aggregate and form crystals. The fuel starts to appear cloudy once the crystals become larger than one quarter of the wavelengths of visible light - this is the cloud point (CP). As the fuel is cooled further these crystals become larger. The lowest temperature at which fuel can pass through a 45 micrometre filter is the cold filter plugging point (CFPP). As biodiesel is cooled further it will gel and then solidify. Within Europe, there are differences in the CFPP requirements between countries. This is reflected in the different national standards of those countries. The temperature at which pure (B100) biodiesel starts to gel, varies significantly and depends upon the mix of esters and therefore the feedstock oil used to produce the biodiesel. For example, biodiesel produced from low erucic acid varieties of canola seed (RME) starts to gel at approximately −10 °C (14 °F). Biodiesel produced from tallow tends to gel at around +16 °C (61 °F). There are a number of commercially available additives that will significantly lower the pour point and cold filter plugging point of pure biodiesel. Winter operation is also possible by blending biodiesel with other fuel oils including #2 low sulfur diesel fuel and #1 diesel / kerosene.
Another approach to facilitate the use of biodiesel in cold conditions is by employing a second fuel tank for biodiesel in addition to the standard diesel fuel tank. The second fuel tank can be insulated and a heating coil using engine coolant is run through the tank. The fuel tanks can be switched over when the fuel is sufficiently warm. A similar method can be used to operate diesel vehicles using straight vegetable oil.
Contamination by water
Biodiesel may contain small but problematic quantities of water. Although it is not miscible with water, it is, like ethanol, hygroscopic (absorbs water from atmospheric moisture). One of the reasons biodiesel can absorb water is the persistence of mono and diglycerides left over from an incomplete reaction. These molecules can act as an emulsifier, allowing water to mix with the biodiesel. In addition, there may be water that is residual to processing or resulting from storage tank condensation. The presence of water is a problem because:
Water reduces the heat of combustion of the bulk fuel. This means more smoke, harder starting, less power.
Water causes corrosion of vital fuel system components: fuel pumps, injector pumps, fuel lines, etc.
Water & microbes cause the paper element filters in the system to fail (rot), which in turn results in premature failure of the fuel pump due to ingestion of large particles.
Water freezes to form ice crystals near 0 °C (32 °F). These crystals provide sites for nucleation and accelerate the gelling of the residual fuel.
Water accelerates the growth of microbe colonies, which can plug up a fuel system. Biodiesel users who have heated fuel tanks therefore face a year-round microbe problem.
Additionally, water can cause pitting in the pistons on a diesel engine.
Previously, the amount of water contaminating biodiesel has been difficult to measure by taking samples, since water and oil separate. However, it is now possible to measure the water content using water-in-oil sensors.
Water contamination is also a potential problem when using certain chemical catalysts involved in the production process, substantially reducing catalytic efficiency of base (high pH) catalysts such as potassium hydroxide. However, the super-critical methanol production methodology, whereby the transesterification process of oil feedstock and methanol is effectuated under high temperature and pressure, has been shown to be largely unaffected by the presence of water contamination during the production phase.
Availability and prices
Biodiesel around the world.
In some countries biodiesel is less expensive than conventional diesel
Global biodiesel production reached 3.8 million tons in 2005. Approximately 85% of biodiesel production came from the European Union.
In 2007, in the United States, average retail (at the pump) prices, including federal and state fuel taxes, of B2/B5 were lower than petroleum diesel by about 12 cents, and B20 blends were the same as petrodiesel. However, as part as a dramatic shift in diesel pricing over the last year, by July 2009, the US DOE was reporting average costs of B20 15 cents per gallon higher than petroleum diesel ($2.69/gal vs. $2.54/gal). B99 and B100 generally cost more than petrodiesel except where local governments provide a tax incentive or subsidy.
Production
Biodiesel production.
Biodiesel is commonly produced by the transesterification of the vegetable oil or animal fat feedstock. There are several methods for carrying out this transesterification reaction including the common batch process, supercritical processes, ultrasonic methods, and even microwave methods.
Chemically, transesterified biodiesel comprises a mix of mono-alkyl esters of long chain fatty acids. The most common form uses methanol (converted to sodium methoxide) to produce methyl esters (commonly referred to as Fatty Acid Methyl Ester - FAME) as it is the cheapest alcohol available, though ethanol can be used to produce an ethyl ester (commonly referred to as Fatty Acid Ethyl Ester - FAEE) biodiesel and higher alcohols such as isopropanol and butanol have also been used. Using alcohols of higher molecular weights improves the cold flow properties of the resulting ester, at the cost of a less efficient transesterification reaction. A lipid transesterification production process is used to convert the base oil to the desired esters. Any free fatty acids (FFAs) in the base oil are either converted to soap and removed from the process, or they are esterified (yielding more biodiesel) using an acidic catalyst. After this processing, unlike straight vegetable oil, biodiesel has combustion properties very similar to those of petroleum diesel, and can replace it in most current uses.
A by-product of the transesterification process is the production of glycerol. For every 1 tonne of biodiesel that is manufactured, 100 kg of glycerol are produced. Originally, there was a valuable market for the glycerol, which assisted the economics of the process as a whole. However, with the increase in global biodiesel production, the market price for this crude glycerol (containing 20% water and catalyst residues) has crashed. Research is being conducted globally to use this glycerol as a chemical building block. One initiative in the UK is The Glycerol Challenge.
Usually this crude glycerol has to be purified, typically by performing vacuum distillation. This is rather energy intensive. The refined glycerol (98%+ purity) can then be utilised directly, or converted into other products. The following announcements were made in 2007: A joint venture of Ashland Inc. and Cargill announced plans to make propylene glycol in Europe from glycerol and Dow Chemical announced similar plans for North America. Dow also plans to build a plant in China to make epichlorhydrin from glycerol. Epichlorhydrin is a raw material for epoxy resins.
Production levels
For more details on this topic, see Biodiesel around the world.
In 2007, biodiesel production capacity was growing rapidly, with an average annual growth rate from 2002-06 of over 40%. For the year 2006, the latest for which actual production figures could be obtained, total world biodiesel production was about 5-6 million tonnes, with 4.9 million tonnes processed in Europe (of which 2.7 million tonnes was from Germany) and most of the rest from the USA. In 2008 production in Europe alone had risen to 7.8 million tonnes.In July 2009, a duty was added to American imported biodiesel in the European Union in order to balance the competition from European, especially German producers.The capacity for 2008 in Europe totalled 16 million tonnes. This compares with a total demand for diesel in the US and Europe of approximately 490 million tonnes (147 billion gallons).Total world production of vegetable oil for all purposes in 2005/06 was about 110 million tonnes, with about 34 million tonnes each of palm oil and soybean oil.
Biodiesel feedstocks
Plant oils
Soybeans are used as a source of biodiesel
Types
Vegetable fats (list)
Macerated (list)
Uses
Drying oil - Oil paint
Cooking oil
Fuel - Biodiesel
Components
Saturated fat
Monounsaturated fat
Polyunsaturated fat
Trans fat
A variety of oils can be used to produce biodiesel. These include:
Virgin oil feedstock; rapeseed and soybean oils are most commonly used, soybean oil alone accounting for about ninety percent of all fuel stocks in the US. It also can be obtained from field pennycress and jatropha and other crops such as mustard, flax, sunflower, palm oil, coconut, hemp (see List of vegetable oils for more information);
Waste vegetable oil (WVO);
Animal fats including tallow, lard, yellow grease, chicken fat, and the by-products of the production of Omega-3 fatty acids from fish oil.
Algae, which can be grown using waste materials such as sewage and without displacing land currently used for food production.
Oil from halophytes such as salicornia bigelovii, which can be grown using saltwater in coastal areas where conventional crops cannot be grown, with yields equal to the yields of soybeans and other oilseeds grown using freshwater irrigation
Many advocates suggest that waste vegetable oil is the best source of oil to produce biodiesel, but since the available supply is drastically less than the amount of petroleum-based fuel that is burned for transportation and home heating in the world, this local solution does not scale well.
Animal fats are a by-product of meat production. Although it would not be efficient to raise animals (or catch fish) simply for their fat, use of the by-product adds value to the livestock industry (hogs, cattle, poultry). However, producing biodiesel with animal fat that would have otherwise been discarded could replace a small percentage of petroleum diesel usage. Today, multi-feedstock biodiesel facilities are producing high quality animal-fat based biodiesel. Currently, a 5-million dollar plant is being built in the USA, with the intent of producing 11.4 million litres (3 million gallons) biodiesel from some of the estimated 1 billion kg (2.2 billion pounds) of chicken fat produced annually at the local Tyson poultry plant. Similarly, some small-scale biodiesel factories use waste fish oil as feedstock. An EU-funded project (ENERFISH) suggests that at a Vietnamese plant to produce biodiesel from catfish (basa, also known as pangasius), an output of 13 tons/day of biodiesel can be produced from 81 tons of fish waste (in turn resulting from 130 tons of fish). This project utilises the biodiesel to fuel a CHP unit in the fish processing plant, mainly to power the fish freezing plant.
Quantity of feedstocks required
Current worldwide production of vegetable oil and animal fat is not sufficient to replace liquid fossil fuel use. Furthermore, some object to the vast amount of farming and the resulting fertilization, pesticide use, and land use conversion that would be needed to produce the additional vegetable oil. The estimated transportation diesel fuel and home heating oil used in the United States is about 160 million tons (350 billion pounds) according to the Energy Information Administration, US Department of Energy -. In the United States, estimated production of vegetable oil for all uses is about 11 million tons (24 billion pounds) and estimated production of animal fat is 5.3 million tonnes (12 billion pounds).
If the entire arable land area of the USA (470 million acres, or 1.9 million square kilometers) were devoted to biodiesel production from soy, this would just about provide the 160 million tonnes required (assuming an optimistic 98 US gal/acre of biodiesel). This land area could in principle be reduced significantly using algae, if the obstacles can be overcome. The US DOE estimates that if algae fuel replaced all the petroleum fuel in the United States, it would require 15,000 square miles (38,849 square kilometers), which is a few thousand square miles larger than Maryland, or 1.3 Belgiums, assuming a yield of 140 tonnes/hectare (15,000 US gal/acre). Given a more realistic yield of 36 tonnes/hectare (3834 US gal/acre) the area required is about 152,000 square kilometers, or roughly equal to that of the state of Georgia or England and Wales. The advantages of algae are that it can be grown on non-arable land such as deserts or in marine environments, and the potential oil yields are much higher than from plants.
Yield
Feedstock yield efficiency per unit area affects the feasibility of ramping up production to the huge industrial levels required to power a significant percentage of vehicles.
Some typical yields
Crop Yield
L/ha US gal/acre
Algae[n 1] ~3,000 ~300, 1500-3000
Chinese tallow[n 2][n 3] 907 97
Palm oil[n 4] 4752 508
Coconut 2151 230
Rapeseed[n 4] 954 102
Soy (Indiana)[58] 554-922 59.2-98.6
Peanut[n 4] 842 90
Sunflower[n 4] 767 82
Hemp[citation needed] 242 26
^ est.- see soy figures and DOE quote below. The larger estimates comes from the New York Times, "Colorado Company to Take Algae-Based Fuel to the Next Level," 11 Nov 2008, M.L. Wald
^ Klass, Donald, "Biomass for Renewable Energy, Fuels,
and Chemicals", page 341. Academic Press, 1998.
^ Kitani, Osamu, "Volume V: Energy and Biomass Engineering,
CIGR Handbook of Agricultural Engineering", Amer Society of Agricultural, 1999.
^ a b c d "Biofuels: some numbers". Grist.org. Retrieved 2010-03-15.
Algae fuel yields have not yet been accurately determined, but DOE is reported as saying that algae yield 30 times more energy per acre than land crops such as soybeans. Yields of 36 tonnes/hectare are considered practical by Ami Ben-Amotz of the Institute of Oceanography in Haifa, who has been farming Algae commercially for over 20 years.
Jatropha has been cited as a high-yield source of biodiesel but yields are highly dependent on climatic and soil conditions. The estimates at the low end put the yield at about 200 US gal/acre (1.5-2 tonnes per hectare) per crop; in more favorable climates two or more crops per year have been achieved. It is grown in the Philippines, Mali and India, is drought-resistant, and can share space with other cash crops such as coffee, sugar, fruits and vegetables. It is well-suited to semi-arid lands and can contribute to slow down desertification, according to its advocates.
Efficiency and economic arguments
Pure biodiesel (B-100) from soybeans
According to a study by Drs. Van Dyne and Raymer for the Tennessee Valley Authority, the average US farm consumes fuel at the rate of 82 litres per hectare (8.75 US gal/acre) of land to produce one crop. However, average crops of rapeseed produce oil at an average rate of 1,029 L/ha (110 US gal/acre), and high-yield rapeseed fields produce about 1,356 L/ha (145 US gal/acre). The ratio of input to output in these cases is roughly 1:12.5 and 1:16.5. Photosynthesis is known to have an efficiency rate of about 3-6% of total solar radiation[64] and if the entire mass of a crop is utilized for energy production, the overall efficiency of this chain is currently about 1% While this may compare unfavorably to solar cells combined with an electric drive train, biodiesel is less costly to deploy (solar cells cost approximately US$1,000 per square meter) and transport (electric vehicles require batteries which currently have a much lower energy density than liquid fuels).
However, these statistics by themselves are not enough to show whether such a change makes economic sense. Additional factors must be taken into account, such as: the fuel equivalent of the energy required for processing, the yield of fuel from raw oil, the return on cultivating food, the effect biodiesel will have on food prices and the relative cost of biodiesel versus petrodiesel.
The debate over the energy balance of biodiesel is ongoing. Transitioning fully to biofuels could require immense tracts of land if traditional food crops are used (although non food crops can be utilized). The problem would be especially severe for nations with large economies, since energy consumption scales with economic output.
If using only traditional food plants, most such nations do not have sufficient arable land to produce biofuel for the nation's vehicles. Nations with smaller economies (hence less energy consumption) and more arable land may be in better situations, although many regions cannot afford to divert land away from food production.
For third world countries, biodiesel sources that use marginal land could make more sense; e.g., honge oil nuts grown along roads or jatropha grown along rail lines.
In tropical regions, such as Malaysia and Indonesia, plants that produce palm oil are being planted at a rapid pace to supply growing biodiesel demand in Europe and other markets. It has been estimated in Germany that palm oil biodiesel has less than one third of the production costs of rapeseed biodiesel. The direct source of the energy content of biodiesel is solar energy captured by plants during photosynthesis. Regarding the positive energy balance of biodiesel:
When straw was left in the field, biodiesel production was strongly energy positive, yielding 1 GJ biodiesel for every 0.561 GJ of energy input (a yield/cost ratio of 1.78).
When straw was burned as fuel and oilseed rapemeal was used as a fertilizer, the yield/cost ratio for biodiesel production was even better (3.71). In other words, for every unit of energy input to produce biodiesel, the output was 3.71 units (the difference of 2.71 units would be from solar energy).
Energy security
One of the main drivers for adoption of biodiesel is energy security. This means that a nation's dependence on oil is reduced, and substituted with use of locally available sources, such as coal, gas, or renewable sources. Thus a country can benefit from adoption of biofuels, without a reduction in greenhouse gas emissions. While the total energy balance is debated, it is clear that the dependence on oil is reduced. One example is the energy used to manufacture fertilizers, which could come from a variety of sources other than petroleum. The US National Renewable Energy Laboratory (NREL) states that energy security is the number one driving force behind the US biofuels programme, and a White House "Energy Security for the 21st Century" paper makes it clear that energy security is a major reason for promoting biodiesel.The EU commission president, Jose Manuel Barroso, speaking at a recent EU biofuels conference, stressed that properly managed biofuels have the potential to reinforce the EU's security of supply through diversification of energy sources.
Environmental effects
Environmental issues with biodiesel
The surge of interest in biodiesels has highlighted a number of environmental effects associated with its use. These potentially include reductions in greenhouse gas emissions, deforestation, pollution and the rate of biodegradation.
According to the EPA's Renewable Fuel Standards Program Regulatory Impact Analysis, released in February 2010, biodiesel from soy oil results, on average, in a 57% reduction in greenhouse gases compared to fossil diesel, and biodiesel produced from waste grease results in an 86% reduction. See chapter 2.6 of the EPA report for more detailed information.
Food, land and water vs. fuel
Food vs fuel
In some poor countries the rising price of vegetable oil is causing problems. Some propose that fuel only be made from non-edible vegetable oils such as camelina, jatropha or seashore mallow which can thrive on marginal agricultural land where many trees and crops will not grow, or would produce only low yields.
Others argue that the problem is more fundamental. Farmers may switch from producing food crops to producing biofuel crops to make more money, even if the new crops are not edible. The law of supply and demand predicts that if fewer farmers are producing food the price of food will rise. It may take some time, as farmers can take some time to change which things they are growing, but increasing demand for first generation biofuels is likely to result in price increases for many kinds of food. Some have pointed out that there are poor farmers and poor countries who are making more money because of the higher price of vegetable oil.
Biodiesel from sea algae would not necessarily displace terrestrial land currently used for food production and new algaculture jobs could be created.
Current research
There is ongoing research into finding more suitable crops and improving oil yield. Using the current yields, vast amounts of land and fresh water would be needed to produce enough oil to completely replace fossil fuel usage. It would require twice the land area of the US to be devoted to soybean production, or two-thirds to be devoted to rapeseed production, to meet current US heating and transportation needs.
Specially bred mustard varieties can produce reasonably high oil yields and are very useful in crop rotation with cereals, and have the added benefit that the meal leftover after the oil has been pressed out can act as an effective and biodegradable pesticide.
The NFESC, with Santa Barbara-based Biodiesel Industries is working to develop biodiesel technologies for the US navy and military, one of the largest diesel fuel users in the world.
A group of Spanish developers working for a company called Ecofasa announced a new biofuel made from trash. The fuel is created from general urban waste which is treated by bacteria to produce fatty acids, which can be used to make biodiesel.
Algal biodiesel
Algaculture and Algal fuel
From 1978 to 1996, the U.S. NREL experimented with using algae as a biodiesel source in the "Aquatic Species Program". A self-published article by Michael Briggs, at the UNH Biodiesel Group, offers estimates for the realistic replacement of all vehicular fuel with biodiesel by utilizing algae that have a natural oil content greater than 50%, which Briggs suggests can be grown on algae ponds at wastewater treatment plants. This oil-rich algae can then be extracted from the system and processed into biodiesel, with the dried remainder further reprocessed to create ethanol.
The production of algae to harvest oil for biodiesel has not yet been undertaken on a commercial scale, but feasibility studies have been conducted to arrive at the above yield estimate. In addition to its projected high yield, algaculture — unlike crop-based biofuels — does not entail a decrease in food production, since it requires neither farmland nor fresh water. Many companies are pursuing algae bio-reactors for various purposes, including scaling up biodiesel production to commercial levels.
Fungi
A group at the Russian Academy of Sciences in Moscow published a paper in September 2008, stating that they had isolated large amounts of lipids from single-celled fungi and turned it into biodiesel in an economically efficient manner. More research on this fungal species; Cunninghamella japonica, and others, is likely to appear in the near future.
The recent discovery of a variant of the fungus Gliocladium roseum points toward the production of so-called myco-diesel from cellulose. This organism was recently discovered in the rainforests of northern Patagonia and has the unique capability of converting cellulose into medium length hydrocarbons typically found in diesel fuel.
Biodiesel from used coffee grounds
Researchers at the University of Nevada, Reno, have successfully produced biodiesel from oil derived from used coffee grounds. Their analysis of the used grounds showed a 10% to 15% oil content (by weight). Once the oil was extracted, it underwent conventional processing into biodiesel. It is estimated that finished biodiesel could be produced for about one US dollar per gallon. Further, it was reported that "the technique is not difficult" and that "there is so much coffee around that several hundred million gallons of biodiesel could potentially be made annually." However, even if all the coffee grounds in the world were used to make fuel, the amount produced would be less than 1 percent of the diesel used in the United States annually. “It won’t solve the world’s energy problem,” Dr. Misra said of his work.
(source:wikipedia)
